It starts early in the design process. But at that stage, it would be best to pause installation, have a mechanical engineer do the mechanical design (including equipment selection) based on an energy model and install the recommended equipment.
It starts early in the design process. But at that stage, it would be best to pause installation, have a mechanical engineer do the mechanical design (including equipment selection) based on an energy model and install the recommended equipment.
I work in building science. It’s obscene how little actual design and quality control goes into residential homes.
The typical design is just one step above being illegal, and people are often scared off of doing anything more than that by the threat of increased cost. However, they don’t realize that they pay for it either way; either on their mortgage, or on utilities. Only one of those you can actually own in the end.
I perhaps haven’t played since the ground handling update, but tailwheel aircraft never behaved like actual tailwheel aircraft. Their steering seemed coupled to the rudder, similar to nose wheel aircraft, instead of having any of the momentum effects of a tailwheel with just a loose steering influence.
I believe the airport was a mid-sized towered airport in Idaho. I forget exactly which though. I selected it as my home base for Neofly because of the scenery and was disappointed when it seemed rather incomplete.
I feel it would’ve been ahead of where it was if it took the aviation side of FSX and paired it with the scenery, weather, and online features of MSFS.
I had FS2020 working well with yoke and pedals and a streamdeck, but it just didn’t feel like a complete sim. Many airports just weren’t there or had incorrectly labeled taxiways, which threw off taxi instructions and obviously made real world charts useless. Tailwheel aircraft didn’t really work properly at all.
Sure, it was a beautiful sim, but was quite lacking on the technical side. I’m doubtful a whole new product is going to solve any of those issues.
I was going to also post the direct AMA link, but the OP is a nice concise summary of many of the key discussions, provided without having to go to that site. I’d recommend reading that instead and follow links as you see fit.
Sorry, four of the power to ethernet plugs. You put one near your router to essentially supply internet to your house’s electrical circuits, then distribute the others where you need them, such as office, living room if you want to connect a TV or console, etc.
I had a set of four for getting ethernet around the few places I rented. There was maybe the odd quality decrease when there was a lot of electrical load, but they worked great otherwise.
“Our Computer”
Oh man, I remember a Philips mp3 player I had for the longest time as a kid. You could hear the little clicks of the hard drive. Lost it on a hike, unfortunately.
They’re not mega saturated, they’re overexposed, which isn’t atypical when photographing at night. Most pictures you’d see of the milky way were captured this way.
And also that many contracts to improve on IT are performed by the lowest bidder.
I remember there being tube polo as an intramural sport at my university. I never played but it’s another option to avoid mostly just drowning the whole time.
I recently went this route after dabbling with other options. I had a wireguard VPN through my Unifi router, with rules to limit access to only the resources I wanted to share, but it can be a struggle for non savvy users, and even more so if they want to use Jellyfin on their TV. Tried Twingate too and would recommend if it fits your usecase, but Cloudflare Tunnels were more applicable to me.
This is mostly my reasoning too. I’ve got a bit more juice than a NUC, but I prefer the way resources are managed with an LXC for the certain apps that I run. I still have VMs for other things, like HAOS and a BlueIris NVR. It’s only a local homelab with no external users so avoiding additional complexity is often in my best interest.
Why would one prefer a VM over an LXC for Docker?
I might have found the issue, see updates above. I have a separate Docker LXC that was behaving normally too, so was good to cross-check with that.
Docker is installed on a Debian container with Proxmox as the hypervisor. I believe as far as Docker knows, it’s just running on normal Debian. The Debian LXC has its own local ip.
I’ll take a look at those resources though, thanks.
Many local libraries provide access to this incredible resource too. Check yours to see.
“Ground, it’s Fred. Off to work. Request taxi to the road.”
“Fred, Ground, roger. Taxi bravo three, left on Juliet, cross runway 34 right, right on foxtrot to the gate. I’ll let security know you’re on the way. Have a good day.”